静电纺丝高压电源多通道电压梯度控制在纳米纤维直径均匀性中的应用

  Electrospinning draws a fibre from a polymer solution by electrostatic force, and the fibre diameter depends on the charge density on the jet, the flow rate and the solvent evaporation. The charge density is set by the applied field, so the supply that sets the field also sets the diameter. In a multi-nozzle arrangement the field at each nozzle must be the same, otherwise the nozzles produce fibres of different diameters and the mat becomes non-uniform.

  A single supply feeding all nozzles through a common electrode produces a field that is highest at the nozzles near the electrode and lower at the far ones. The variation is a few percent across a small array and can reach twenty percent across a large one. The consequence is a mat with a diameter gradient that is visible in the mechanical properties.
  Multi-channel control solves that by giving each nozzle its own channel with its own setpoint, derived from a model of the field distribution. The model can be as simple as a weighting function fitted from a one-time measurement with a field probe, and the fitted weights then compensate the geometric variation for any pattern of active nozzles.
  Crosstalk between channels is the main design difficulty. The channels share a common return and a common high voltage bus, and a change on one channel couples into the neighbours through the bus impedance. Decoupling the bus with local storage at each channel, and staggering the switching of the channel regulators so their ripple does not align, keeps the crosstalk below a level that matters for the diameter uniformity.
  The current per channel is small, in the microampere range, so the measurement must be designed for that range. A high value sense resistor gives a usable signal but introduces a voltage drop that changes the nozzle potential. A transimpedance amplifier avoids that drop, and its bandwidth must be high enough to follow the jet, which can oscillate at a few hundred hertz when the flow rate is unstable.
  Nozzle interaction through the jet's own charge is the second order effect. Charged jets repel each other, and in a dense array the repulsion pushes the jets outward, which changes the landing position on the collector and thins the mat at the centre. Compensating with a slight increase of field at the inner nozzles keeps the landing position even, and the compensation depends on the number of active nozzles, so the channel setpoints should be computed from the active pattern rather than stored as a fixed table.
  Collector design interacts with the field. A conductive collector at a fixed distance gives a field that depends only on the nozzle voltage, whereas a moving belt collector introduces a varying distance and therefore a varying field unless the voltage is modulated with position. For a production line the modulation is worth implementing, because the diameter uniformity across the belt width is one of the properties that customers measure.
  Solvent evaporation is the variable that makes the process difficult to reproduce. A jet that evaporates slowly reaches the collector wet and flattens, which produces a ribbon rather than a fibre. A jet that evaporates quickly solidifies before reaching the collector, which produces a fibre that is thinner than intended and sometimes discontinuous. The field affects the evaporation by accelerating the jet and shortening the transit time, so the field setpoint and the ambient humidity must be considered together rather than independently.
  Safety design for a multi-channel spinning head follows the same rules as for a single channel, with one addition: the channels must all be de-energised together when the enclosure opens. A per-channel interlock allows one channel to remain live while an operator reaches into the enclosure to clear a blockage, which is precisely when contact is most likely. A common interlock relay in the primary path of every channel, with a forced-guided contact that is monitored, gives the required behaviour.
  Records for a production run should include the channel setpoints, the per-channel current, the humidity and the collector speed. A mat that fails a diameter measurement can then be traced back to the channel that drifted, and the drift is usually a blocked nozzle rather than an electrical fault. Distinguishing the two from the current signature saves a service visit.
  Calibration of the field at each nozzle is best done with a probe that is inserted at the collector plane, because the field at the nozzle itself is dominated by the nozzle geometry and does not represent the field that draws the jet. A calibration at the collector plane, repeated after any change of nozzle array, gives the setpoints a physical meaning and makes the compensation table transferable between machines.
  Throughput and quality pull in opposite directions in a spinning line. A higher field draws a thinner fibre and raises the throughput, but the thinner fibre is weaker and the mat becomes fragile. A lower field gives a thicker fibre and a stronger mat at a lower rate. The operating point that satisfies both is narrow, and holding it requires the field to be stable to a few percent over a shift. A multi-channel supply with per-channel regulation achieves that stability more easily than a single supply with a common electrode, because each channel can correct its own drift.
  Polymer solution ageing is the chemical variable that mimics an electrical fault. A solution that has been standing changes viscosity and conductivity, and a more conductive solution draws more current at the same field, which the supply may interpret as a fault. A current limit set with enough headroom, plus a conductivity measurement recorded with each batch, keeps the electrical protection from stopping a run that is merely using an aged solution.
  The collector's surface condition affects the field in the gap between the jet and the collector. A collector that has accumulated a thick insulating mat charges and reduces the field, which changes the diameter during a long run. Grounding the collector through a low impedance, and removing the mat at defined intervals, keeps the gap field constant. Measuring the collector current as a trend gives the interval a physical basis rather than a guess.
  Multi-channel control has one advantage that is easy to overlook: a single channel failing can be isolated without stopping the whole line. A channel that loses its output is detected by its current signature, and the line can continue with reduced coverage while the channel is repaired. In a production environment that availability is worth more than the last few percent of uniformity.
  Commissioning a multi-channel head should include a uniformity test that produces a mat whose fibre diameter is measured at several positions across the width. The measurements become the baseline for later comparisons, and the comparison is what distinguishes a channel that has drifted from a solution that has aged. Without the baseline every complaint starts from the beginning.
  The design summary for this application is that the supply is a distribution system as much as a voltage source. Distributing the field evenly, measuring each channel's current and compensating the interaction between channels are the functions that determine whether the mat meets its specification, and the voltage accuracy of any single channel is only the starting condition.
  Availability is the second benefit of per-channel isolation, and a line that keeps running while one channel is repaired returns more value over a year than a line that stops for every electrical fault.
  Measurement of fibre diameter is the acceptance test that ties the electrical work to the product, and the measurement should be taken at several positions on a mat produced under the same conditions as production. A mat measured once at the centre tells little, because the non-uniformity that matters is the variation across the width, and that variation is exactly what the per-channel compensation is intended to remove.
  When the variation exceeds the specification, the first check is the channel current signature, the second is the field probe at the collector plane, and the third is the solution conductivity. Checking in that order follows the likelihood of the cause, and it shortens the time from a rejected mat to a corrected line.
  The order of checks follows the likelihood of the cause, and following it keeps a spinning line productive while the correction is identified and applied without stopping the whole array.
  A head that is calibrated at the collector plane, compensated for nozzle interaction and monitored per channel produces a mat whose diameter varies less across the width than along the length, and that is the uniformity the specification is written for.
  A line that documents its channel setpoints, its compensation table and its collector calibration can transfer a mat specification to a second machine without repeating the development, and that transferability is what turns a laboratory process into production.
  Transferability is the property that distinguishes a production process from a laboratory demonstration, and documentation is what makes it transferable.